| Products | Product Series | Product Introduction | Category | Key Performance Description | |
Polishing Pad | Wafer Polishing Hard Pad | Polishing hard pads are core consumables in chemical mechanical polishing (CMP) processes. They remove materials from the wafer surface and achieve nanometer-level flatness through the synergistic effect of mechanical friction and chemical corrosion. | DH3XXX Series DH5XXX Series DH7XXX Series | High-hardness series products, featuring high planarization efficiency, high grinding removal rate, and long service life. | |
| Medium-hardness series products, offering a good balance in grinding removal rate, defect rate, and service life. | |||||
| Low-hardness series products, effectively reducing the defect rate and improving product yield. | |||||
Large Silicon Wafer Polishing Pad/Wafer Polishing Soft Pad | Polishing soft pads are core consumables in chemical mechanical polishing (CMP) processes, mainly used for fine polishing and final polishing. Compared with hard pads, soft pads have better surface adaptability, reducing scratches and improving smoothness. | DR90XX Series | Structure: "PU + polyester polymer film substrate"; Density: 0.150-0.450g/cm 3 ; Hardness: 4HA-45HA; Features low defect rate and high stability. | ||
DR91XX Series | Structure: "PU + non-woven fabric"; Density: 0.200-0.600g/cm 3 ; Hardness: 20HA-70HA; Features low defect rate and long service life. | ||||
DR96XX Series | Structure: "PU-impregnated polyester fiber composite material"; Density: 0.200-0.700g/cm 3 ; Hardness: 30HA-95HA; Features high grinding removal rate and long service life. | ||||
Third-Generation Semiconductor Polishing Pad | Third-generation semiconductor polishing pads are core consumables in chemical mechanical polishing (CMP) processes. They remove materials from the wafer surface and achieve nanometer-level flatness through the synergistic effect of chemical corrosion and mechanical grinding. Due to the high hardness of SiC and GaN (SiC Mohs hardness is 9.5), traditional polishing pads cannot meet the requirements. Therefore, special materials and structural designs are used to balance hardness and flexibility and reduce surface defects. | EPXXXX Series | Density: 0.400~1.030g/cm 3 ; Hardness: 20HD-90HD; Using special processes and product designs to achieve the manufacturing of ultra-large-size polishing pads to meet the equipment needs of this field; Through special micro-pore control technology, the pore size and porosity can be controlled, effectively reducing TTV (total thickness variation); Using a closed-pore design to improve the corrosion resistance and product stability of the polishing pad. | ||
DR95XX Series | Density: 0.150-0.450g/cm 3 ; Hardness: 10HA-30HA; Using special processes and product designs to achieve the manufacturing of ultra-large-size polishing pads to meet the equipment needs of this field; Through special formula design to meet the needs of low roughness. | ||||
Polishing Liquid | DP53XX, DP55XX, DP59XX Series | Used in the integrated circuit manufacturing process for the removal and planarization of polysilicon, it features a high polysilicon removal rate, high dilution ratio, and low defect rate. The product has been used in mass production of memory devices. | Polysilicon Polishing Liquid | Solid content: 4%-20%; Particle size: 60-200 nm; Poly/OX selectivity >10 | |
DP54XX, DP56XX, DP58XX Series | Used in the integrated circuit manufacturing process for the removal and planarization of silicon nitride in STI buff/ILD/SAC processes, it features strong dishing effect repair capability and precise control of gate height, and is widely used in the manufacturing of 28nm/14nm logic devices. | Silicon Nitride Polishing Liquid | Solid content: 2%-20%; Particle size: 50-100 nm; SiN/OX selectivity: 2~5 | ||
ZX Series | Used in the integrated circuit manufacturing process for the removal and planarization of dielectric materials (silicon oxide), it features a high removal rate, high dilution ratio, and low defect rate. The product has been used in mass production of memory devices. | Dielectric Material Polishing Liquid | Solid content: 3%-20%, Particle size: 80-150nm, OX RR>3000A/min | ||
DP6XXX Series | In integrated circuit manufacturing, it is used for chemical mechanical polishing (CMP) of the silicon wafer surface, and has the characteristics of high removal rate and low surface defect rate. | Silicon Substrate Polishing Liquid | Solid content: 2%-20%; Particle size: 50-100 nm; Si RR>10000A/min; Number of defects less than 10 (0.160μm) | ||
DW6XXX Series | Equipped with self-produced alumina abrasive particles, it is used for the removal and planarization of tungsten gate materials in the logic device manufacturing process, and has the characteristics of high planarization efficiency, high selectivity, and low defect rate. The product has been used in mass production of advanced process logic devices. | Tungsten Gate Polishing Liquid | Solid content 0.01%-0.3%, particle size 60-120nm, W RR 100-1500A/min, TiN RR 100-1000A/min, OX RR <20A/min, W/OX selectivity >50 | ||
DW3XXX, DW5XXX series | Used for the removal and planarization of tungsten metal in integrated circuit manufacturing processes. Selectivity is controllable to meet customized selectivity requirements, with a low defect rate, suitable for high-order or advanced processes. It has been used in mass production in logic device production. | Tungsten polishing liquid | Solid content 1%-10%, particle size 60-100nm, W RR 50-1000A/min, TiN RR 100-2000A/min, OX RR 100-1000A/min, W/OX selectivity 1-10. | ||
DB series | Used for the removal and planarization of the barrier layer in the copper interconnect process of integrated circuit manufacturing. Selective polishing of copper and barrier layer, high planarity, low defects, low corrosion or dishing. | Copper barrier layer polishing liquid | Solid content 5~25%, particle size 20-150nm, Cu RR 20-2000A/min; OX RR 300~2000A/min; BD RR 100-700A/min; Ta RR 100-1500A/min; TaN RR 100-3000A/min; SiN RR 100-1000A/mim (customized according to needs) | ||
DC series | Used for the removal and planarization of copper metal in integrated circuit manufacturing processes. It features a high removal rate, high dilution ratio, and low defects. | Copper polishing liquid | Solid content 0.5%-2%, particle size 30-120nm; Cu RR 5000-20000A/min; OX RR<30A/min, high Cu/OX selectivity | ||
ZA series | Equipped with self-produced alumina abrasive particles, it is used for the removal and planarization repair of metal aluminum gate materials in integrated circuit manufacturing processes. It features high planarization efficiency, high selectivity, and a low defect rate. The product has been used in logic device manufacturing. | Aluminum gate polishing liquid | Solid content 0.5%-2%, particle size 60-120nm, Al RR 300-2500A/min, TiN RR 100-2000A/min, OX RR <30A/min, Al/OX selectivity >50 | ||
DS series | Equipped with self-produced cerium oxide abrasive particles, it is used for the removal and planarization of dielectric materials (silicon dioxide) in integrated circuit manufacturing processes, in the construction of STI structures. It features a high silicon dioxide removal rate, high planarization efficiency, low dishing effect, and a low defect rate. | Cerium oxide polishing liquid | Solid content 0.5%-5%, particle size 80-150nm, OX RR~100-8000A/min (customized according to needs), high OX/SiN selectivity | ||
DLS series | A core raw material in advanced CMP slurry. Widely used in front-end processes and advanced metal interconnect processes. It features low hardness and few defects. | Ultra-pure silicon abrasive | Solid content 15%-21%, particle size 35-180nm; pH 6.5~8.6; various metal impurities <20ppb; customizable positive and negative charges of abrasive | ||
DLSB series | Used in slurry design for various processes in integrated circuit manufacturing. It provides mechanical grinding force and chemical component adsorption sites, and can be used in scenarios requiring fast removal and high selectivity control. | High-purity silicon abrasive | Solid content 20-50%; particle size 20~150nm; pH 8~11; Mohs hardness ~6 | ||
Cleaning solution | DZ38X series | Used in integrated circuit manufacturing, an alkaline formula cleaning solution for post-cleaning of copper metal. Applied in 5-65nm technology nodes, it effectively removes surface particles, organic matter, and metal contaminants, and also has a copper protection function. The product has been used in mass production of memory devices and logic devices. | Post-cleaning solution for metal chemical mechanical polishing | Excellent cleaning effect, high safety performance, high Q-time, different products have a copper corrosion rate ER(Cu)=0.1~3Å/min. | |
DZ611 | Used in integrated circuit manufacturing, an acidic formula cleaning solution for post-cleaning of copper and tungsten metal CMP. It covers mature and advanced process nodes, effectively removing surface particles, organic matter, and metal contaminants. | Excellent cleaning effect, high safety performance, copper corrosion rate ER(Cu)<2Å/min. | |||
DZ101 | Used in integrated circuit manufacturing, a formula cleaning solution for post-cleaning of tungsten and silicon nitride CMP. It shows good cleaning performance in post-CMP processes in self-aligned processes. The product has been used in mass production of logic devices. | The product has good compatibility and cleaning effect on various materials such as W, SiN, TEOS, TiN, and Co. | |||
DZ105 | Used in integrated circuit manufacturing, an acidic formula cleaning solution for removing contamination from tungsten metal. Applied in 14nm-28nm technology nodes, applied to the polishing pad surface, aiming to reduce the degree of contamination in the metal gate process. | The product has extremely low corrosion rates and good cleaning effects on W, SiN, Co, Al, Ti, and TiN. | |||
DZ4XX series | Used in integrated circuit manufacturing, a weakly acidic cleaning solution for post-cleaning of tungsten metal CMP, mainly used for cleaning of 14 nm and below WMG. The product has been used in mass production of logic devices. | The product exhibits excellent cleaning performance on W and TEOS surfaces, and demonstrates good material compatibility with W, SiN, TEOS, TiN, and Co. | |||
DZ6XX series | An acidic cleaning solution used in integrated circuit manufacturing for post-CMP cleaning of aluminum metal, primarily applied in 28nm technology nodes. It features excellent cleaning performance and an extremely low defect rate. The product is currently used in logic device mass production. | The product demonstrates excellent cleaning performance and good compatibility with various materials such as Al and TEOS. It exhibits a low aluminum corrosion rate (ER(Al) < 1Å/min). | |||
DZ1XX series | A formulated cleaning solution used in integrated circuit manufacturing for post-CMP cleaning of polysilicon and silicon nitride, applied to polishing pad surfaces to effectively remove surface particulate contaminants. The product is currently used in logic device mass production. | Cleaning solution for post-CMP of non-metallic materials | The product is compatible with Poly-Si, SiN, and TEOS and can be used for auxiliary cleaning in STI, ILD, ILD0, and Poly processes |